Audi A4

since 1994 release

Manual of the car



Audi A4
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ System of an exhaust
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and channels of absorption
+ System of injection
+ Coupling
+ Transmission and main transfer
- Suspension bracket of wheels and steering
   Running gear
   Check of cuffs of the steering mechanism
   Check of dustproof caps and gap in heads of cross steering draft
   Check of dustproof caps of hinges of an axis
   Check of a side play of a steering wheel
   Check of a maple belt
   Check of level of oil
   Check of a gap of the wheel bearing
   Shock-absorbers
   Check of shock-absorbers
   The help at malfunctions
   Adjustment of wheels
   Measurement of adjustment of wheels
   The help at malfunctions
   Independent works on a running gear and steering
   Dismantling of a suspension bracket of forward wheels
   Works with the back bridge
   Replacement of the shock-absorber behind
   Steering
   Works on steering
   Check of tightness of a servoupravleniye
   Poliklinova belt
   The help at malfunctions
   Adjustment of the steering mechanism
   Dismantle of the pump of a servoupravleniye
   Filling and pumping of system of a servoupravleniye
   Safety cushion
   Instructions of safety
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ System of ignition
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
+ Body details
+ Salon
Search of malfunctions
Technical characteristics


7c8a7ef4



Works on steering

External end of cross steering draft

1 – an adjusting bolt of a convergence of wheels on turn;
2 – tightening bolt of cross steering draft;
3 – head of cross steering draft;

4 – lock-nut;
5 – hexagon of cross steering draft.


The arrow indicates the assembly provision of an adjusting bolt of the steering mechanism.

Replacement of a head of cross steering draft

 PERFORMANCE ORDER

  1. Remove a wheel.
  2. Unscrew самоконтрящуюся a nut on a tightening bolt of cross steering draft.
  3. Take out tightening a bolt.
  4. Unscrew an adjusting bolt of a convergence of wheels on turn.
  5. Squeeze out a head of cross steering draft from a wheel bipod on the case of the wheel bearing down.
  6. Unscrew a lock-nut on a head of cross steering draft, wring out at the same time a hexagon of cross steering draft in an opposite direction.
  7. Designate the provision of screw connection of cross steering draft, then after screwing together width of a track will be approximately the same.
  8. Unscrew a head of cross steering draft, transfer marking to a new head of steering draft.
  9. Installation: press a finger of a head of cross steering draft into a wheel bipod if it is necessary, carefully hammer.
  10. Tighten new самоконтрящуюся a nut on 40 Nanometers.
  11. Tighten also on 40 Nanometers of a lock-nut.
  12. Check a convergence of wheels.

Replacement of cross steering draft assembled

This work sometimes does not work well because of inaccessibility of screw connection between cross steering draft and the steering mechanism. For this screw connection there is V.A.G 1923 key allowing to delay this screw connection on 100 Nanometers. It is recommended for application.

 PERFORMANCE ORDER

  1. Separate a head of cross steering draft from a steering bipod as it is described in the previous section.
  2. Weaken the bellow valve on cross steering draft and the steering mechanism, remove.
  3. Unscrew cross steering draft from a lead of the steering mechanism.
  4. Installation: grease the internal hinge with lubricant for the steering AOF 063 000 04 mechanism.
  5. Screw up new cross steering drafts on a lead of the steering mechanism on 100 Nanometers.
  6. Install the bellow valve.
  7. Fix a head on cross steering draft and a bipod of a wheel as it is described above.
  8. Check a convergence of wheels.