Audi A4
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ System of an exhaust
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and channels of absorption
+ System of injection
+ Coupling
+ Transmission and main transfer
+ Suspension bracket of wheels and steering
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ System of ignition
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
+ Body details
- Salon
Control panel
Average console
Seats
Search of malfunctions
Technical characteristics
|
Seats
Dismantle of front seats
|
|
Dismantle of front seats (model with the lock screw): weaken ahead on a seat the lock screw (1) and disconnect the shtekerny socket (2) – here heating of a seat. |
|
|
Dismantle of front seats: unscrew a stopper (1), wring out a decorative cap (2) and remove the decorative panel (3). |
|
|
- Wring out decorative caps of the panel behind on the internal tire of a seat, weaken the screw, remove the panel back.
- Unscrew on the external tire of a seat the screw with a crosswise head and remove a stopper.
- Disconnect sockets of wires of heating of a seat and the electric drive of adjustment.
- Seats with manual adjustment: unscrew on the average tire of a seat ahead the lock screw.
- The buffer spring is installed in some cars instead of the lock screw.
- Seats with the adjustment electric drive, heating of seats: wring out ahead on the right and at the left on the tire of seats of a covering and unscrew under them screws.
- Ahead lift a seat, open collars of wires, disconnect sockets.
- For all: remove a seat back.
- Before installation check whether so-called rams outside on seat support, and also ahead in the middle are damaged. Otherwise the seat will shake.
|
|
Dismantle of head restraints
|
|
- In sockets which the fixing core of a head restraint enters about one key is integrated.
- Press a key.
- Remove head restraints up.
|
|
Dismantle of a back seat
|
|
Side facing which is outside near the leaning-back back of a back seat is screwed in the middle of (2). Above (1) and below (3) it are only hung. |
Dismantle of a pillow of a seat
|
|
- Lift a seat pillow.
- At installation track that thorns on the lower party of a pillow of a seat entered reception openings under the seat console.
- Dismantle of separate backs: cast away the corresponding back.
- Unscrew the average hinge and remove a part of a back.
- Weaken under it the screw with a crosswise head.
- Take out a part of a back from the average hinge and pull to the middle from a guide on a sidewall.
- Dismantle of side facing near the cast-away seatback: cast away a seatback.
- Weaken from the inside screw connection approximately on the middle of height of side facing.
- Shift side facing up and take out from clips.
- Dismantle of a rigid back: dismantle a seat pillow.
- Dismantle head restraints.
- Carefully take out guides of head restraints from a back of a back seat up.
- Weaken two screw connections at bottom edge of a back.
- Shift a back up and take out from clips.
|
|
Dismantle of a back reception pocket
|
|
- Cast away a back of a back seat and dismantle side facing or a rigid back.
- Lift a back reception pocket for a first line and pull forward, at the same time clamps will leave grooves at the rear edge.
- If to pull a reception pocket a little forward, then it is possible to unscrew the automatic device of a seat belt. For dismantle of loudspeakers it is enough to pull only a reception pocket forward.
|
|
Seat belts
On front seats in Audi there is a pyrotechnic device of a tension of a seat belt. Just as in a safety cushion, at operation the small charge of explosive which tightens belts to the driver and to the passenger near the driver is lit. Just as in case of a safety cushion (the head Podvesk of wheels and steering), the strict safety rules concerning installation and dismantle work for the device of a tension of a seat belt. Dismantle and installation – work for a workshop.
|
|
