Audi A4

since 1994 release

Manual of the car



Audi A4
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ System of an exhaust
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and channels of absorption
+ System of injection
+ Coupling
+ Transmission and main transfer
+ Suspension bracket of wheels and steering
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ System of ignition
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
- Body details
   Front bumper
   Damages to result of accidents
   Frontal part of the car
   Cowl
   Wings
   Side levels
   Doors
   Dismantling of doors
   Mirror of the external review
   Trunk lid
   Rear bumper
   Sliding/removable roof
   Check of a corrosion-resistant coating of the bottom
   Clearing of openings for a water drain
+ Salon
Search of malfunctions
Technical characteristics


7c8a7ef4



Trunk lid

Dismantle

 PERFORMANCE ORDER

  1. Open a cover.
  2. Remove the triangular warning sign.
  3. Unscrew an arm of the warning sign.
  4. Unscrew facing of a trunk lid.
  5. Disconnect the shtekerny socket of wires to electric knots in a trunk lid and stretch the socket through an entrance in metal.
  6. Disconnect a hose of the central lock.
  7. Cast away lock collars on gas-filled shock-absorbers on the right and at the left and remove them. After that it is possible to wring out gas-filled shock-absorbers from spherical heads.
  8. Holding a cover together, unscrew two screws on a loop on the right and at the left.
  9. Uncover a loop.
  10. It is possible to unscrew in addition the hinge from a body.

Adjustment of a trunk lid

Trunk lid loops: 1 and 2 – screws a loop/trunk lid; 3 and 4 – screws a loop/body.


The provision of a plate of the lock with a bolt (2) behind at the bottom of a luggage carrier can be adjusted after weakening of both screws (3). The plate of the lock becomes available after dismantle of facing (1) of edge of a luggage carrier.


 PERFORMANCE ORDER

  1. It is necessary that the crack between a trunk lid and the left, and also right detail of a body was one width (about 3 mm). Back glass between it and a cover on the right and at the left too has to have a crack of identical width.
  2. Adjustment is carried out after weakening of screws of a loop/trunk lid. Besides, the cover has to be in one plane with side details of a body. It can be adjusted after weakening of screws of a loop/sidewall.
  3. If the trunk lid knocks or is badly closed, then it is possible to adjust the persistent shock-absorber on the right and at the left below on a cover:
  4. Weaken the fixing screw and shift up or down and again tighten. Persistent shock-absorbers are installed correctly in case they at the closed cover adjoin without tension.
  5. Check landing and closing of a trunk lid if it is necessary, carry out an additional adjustment of a plate of the lock of a luggage carrier.

Dismantle of the lock of a luggage carrier

 PERFORMANCE ORDER

  1. Open a cover.
  2. Remove a precautionary triangle.
  3. Unscrew an arm of a precautionary triangle.
  4. Unscrew facing of a trunk lid.
  5. Dismantle of a pusher: cast away a lock collar on the operating bar to a key wedge and remove a bar.
  6. Disconnect the socket of the central lock.
  7. Disconnect an air hose of the central lock.
  8. Unscrew two nuts, remove inside the press button with a drum of the lock.
  9. Dismantle of a key wedge: remove the operating bar (cast away sideways a lock collar).
  10. Unscrew two six-sided nuts on a key wedge, take out a key wedge down.