Audi A4
+ Running gear
+ Regular servicing
+ Engines
+ Turbo-supercharging
+ System of an exhaust
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and channels of absorption
+ System of injection
+ Coupling
+ Transmission and main transfer
+ Suspension bracket of wheels and steering
+ Brakes
+ Wheels and tires
+ Electrotechnical equipment
+ System of ignition
+ Lighting
+ Alarm equipment
+ Tools and devices
+ Heating and ventilation
- Body details
Front bumper
Damages to result of accidents
Frontal part of the car
Cowl
Wings
Side levels
Doors
Dismantling of doors
Mirror of the external review
Trunk lid
Rear bumper
Sliding/removable roof
Check of a corrosion-resistant coating of the bottom
Clearing of openings for a water drain
+ Salon
Search of malfunctions
Technical characteristics
|
Cowl
|
|
The gas-filled shock-absorber (1) of a cowl Audi can be dismantled after removal of a lock washer (2) and removal of an eye of the hinge from a finger. |
|
|
The assistant has to hold a heavy cowl before fixing bolts (1 and 2) of a cowl are weakened. |
Dismantle
Itself can facilitate installation of the removed cowl if before demontazhy to note position of hinges. It is the best of all to make it a waterproof felt-tip pen.
|
|
- Where is, weaken fastening of wires of a lamp for illumination of a cowl, heating of sprays of system of washing, and also a tape of connection to weight.
|
|
Council: if the same cowl is established, then at a pulling of a wire fix a cord on its end. Stretch a cord with a wire through a cowl. The cord will remain in a cowl and will help to involve a wire at installation. |
- Disconnect a hose of system of washing of glasses.
- Remove from the top fixing finger or from both fingers a lock clip of the gas-filled shock-absorber.
- Weaken bolts of hinges on the right and at the left.
- Cowl too heavy to unscrew it alone. Therefore hold a cowl with the assistant with right and on the left side.
- Now squeeze out fixing fingers of the gas-filled shock-absorber and remove the shock-absorber.
- Completely unscrew already weakened bolts a hand and remove a cowl.
- If it is required, it is possible to unscrew cowl hinges.
|
|
|
|
Council: All gas-filled shock-absorbers cannot just be thrown out, they need to be brought in the workshop Audi for "decontamination". |
|
|
At the correct installation the cowl has to adjoin to these shock-absorbers (shooter) densely. For adjustment of height the shock-absorber is screwed up or unscrewed. |
|
|
Figures "1" and "2" designated reverse sides of bolts which have to be weakened for adjustment of the lock of a cowl on height. |
|
|
If the locking bracket of a cowl enters the lock not precisely, then it can be shifted after weakening of bolts with six-sided heads (1–3). |
|
|
The cable of unblocking of a cowl ahead enters the cowl lock.
Are designated by figures: 1 – cable cover; 2 – cable cover countersupport; 3 – cowl lock lever; 4 – the nipple on the end of a cable. |
|
|
To replace a cowl cable, weaken bolts with six-sided heads (1 and 2). The cable (4) is on sale only together with the handle (3). |
Adjustment of a cowl
When the cowl is closed, the distance from it to both wings has to be identical (about 3 mm), and on a first line it has to be in one plane with wings. Besides, adjustment on height has to be correct too.
|
|
- For adjustment in the longitudinal direction bolts above between the hinge and a cowl are weakened.
- For side adjustment bolts between the hinge and a body are weakened.
- Shift a cowl cover in the necessary direction and tighten bolts.
- On a first line adjustment of height of a cowl is carried out as follows:
- Screw up persistent shock-absorbers to the edge of metal on the right and at the left.
- Weaken fixing bolts of the lock of a cowl and shift the lock as it is necessary, down or up.
- At this time check installation on height at the closed cowl: the upper edge of a cowl has to be ahead at one height with wings.
- Again tighten fixing bolts of the lock of a cowl.
- Pay attention to that the locking bracket entered a lock opening. If is not present, then the locking plate can be shifted sideways and in the longitudinal direction after weakening of three fixing bolts.
- Unscrew the persistent shock-absorber until the cowl does not cease to shake in a closed position. To reach the correct adjustment, several attempts are required.
|
|
Replacement of a cable of a cowl
|
|
- Open a cowl.
- Hang out from the lock the nipple on the end of a cable.
- Also hang out a cable cover.
- Take out a cable cover from arms. In the field of laying of a cowl it is laid in a laying flute.
|
|
Dismantle a reception pocket under the control panel at the left (the head Salon).
|
|
- Unscrew the unblocking handle in the driver's legs.
- Involve a cowl cable in salon. Be careful, the "obstinate" cable can cause injury of eyes!
- Stretch a new cable through a rubber nozzle from within, track the correct arrangement of a nozzle (dense).
- Screw the unblocking handle.
- Enclose a cable cover in dredging of laying of a cowl, and also in arms on a frontal part of the car.
- Stretch a cable through a countersupport of the lock and hang a cover.
- Hang on the lock the nipple on the end of a cable.
|
|
|
|
